News
-
What should I do if the laser tube has no light?
1. Sewage level switch. 2. High voltage lines are interrupted. 3. The laser tube is broken or burned. 4. The laser power supply is broken. 5. Water circulation “including blocked water pipes and non-working water pumps” 6. The waterproof line is broken or the contact is bad. 7. There ...Read more -
Analysis of deformation of small holes (small diameter and plate thickness) during laser cutting
This is because the machine tool (only for high-power laser cutting machines) does not use blasting and drilling to make small holes, but pulse drilling (soft puncture), which makes the laser energy also concentrated in a small area. The non-processed area will also be burnt, causing hole deforma...Read more -
How to solve the problem of burrs on the workpiece when laser cutting low carbon steel
According to the working and design principles of fiber laser cutting, the analysis shows that the following reasons are the main causes of burrs in the workpiece: The upper and lower positions of the laser focus are incorrect, and the focus position test needs to be performed and adjusted accord...Read more -
How to adjust the uneven marking problem of laser marking machine
Why is the fiber laser marking machine not accurately positioned? 1. The laser spot is locked and the output beam passes through a field mirror or galvanometer. There are shortcomings; 2. There may be damage to the lens, which will cause a mismatch of laser energy when the laser beam is emitted. ...Read more -
Methods and precautions for laser cutting machine parameter adjustment.
For beginners of fiber laser cutting machines, the cutting quality is not good and many parameters cannot be adjusted. Briefly study the problems encountered and their solutions. The parameters to determine the cutting quality are: cutting length, cutting type, focus position, cutting force, cutt...Read more -
Solution for non-light-emitting of laser tube
1. The water level switch is broken. 2. The high voltage wire is broken 3. The laser tube is broken or burnt 4. Laser power is cut off. 5. No water circulation, including clogged water pipes and non-functioning water pumps 6. The water protection line is broken or the contact is not correct. 7. T...Read more -
How to solve the problem of burrs on the workpiece when laser cutting low carbon steel
According to the operation principle and design principle of CO2 laser cutting, the analysis found that the main causes of burrs on the workpiece are: The upper and lower positions of the laser focus are incorrect and a focus position test must be performed. It will be adjusted according to the f...Read more -
Features of laser marking
Because of their unique operating principle, laser marking machines have many advantages over traditional marking methods (pad printing, inkjet coding, electrical corrosion, etc.); 1) No contact processing Marks can be printed on any regular or irregular surface, and the workpiece does not develo...Read more -
Common faults and solutions of laser marking machines
1. The elimination process produces abnormal results 1. The power indicator light does not light up. 1) AC 220V is not connected correctly. 2) The indicator light is broken. Plug in the power cord and replace it. 2. The shield light is on and there is no RF output. 1) Internal overheating, preven...Read more -
What should you pay attention to before working on the fiber laser cutting machine exchange platform?
1. The tool head returns to the reference point position. 2. The security door is closed. 3. The network protection system is in a normal state; 4. No material leaking out of the workbench, and no dust on the exchange table guide rail.Read more -
These factors are key to accurate laser cutting
The main factors that make a laser cutting machine effective are: 1. The size of the spot when the laser beam passes through the focus The small spot when you focus on the laser, which is very precise, especially the small crack, the spot can reach 0.01mm. 2. The accuracy of the workbench determ...Read more -
Why does the fiber laser marking machine have uneven marking results?
1. Use the focal length to dial in a particular point of view: Each focal length has a specific length. If the calculated length is wrong, the engraving result will not be the same. 2. The box is placed in a stable place so that the galvanometer, the field mirror and the reaction table are not th...Read more